221 N Hogan St,

Jacksonville, FL 32202

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

221 N Hogan St,

Jacksonville, FL 32202

How To End Dripping Drain Faucets

Learn to determine the cause of a leaking faucet.

There is absolutely nothing more irritating than a leaking faucet. Not just can it keep you awake at night, however it may likewise cost you more on your water expense. That is why fixing a leaking faucet as soon as possible is usually an excellent idea.

 

It’s an easy DIY project with a few tools and the right information.

 

The repair method will vary based on the type of spout and sink you have, however you can use these standard tips to stop a leaking faucet:

 

  • It is essential to keep an eye out for leaking faucets, as a single leaky component can lose approximately 20 gallons of water every day! Check your sink to attempt to locate the cause of the leak.
  • You’ll require to replace the O-ring or tighten up the packing nut if water is collecting around the faucet’s stem..
  • If the leak is originating from the spout, the faucet handle is more than likely damaged. Now, it is essential to understand what kind of faucet you have in your house.
  • Cartridge Faucets are most typical in modern-day properties, and the cartridge must be replaced on a regular basis.
  • A Compression Faucet, on the other hand, is more typical in older properties. Changing them can normally fix a leaking faucet since the rubber seals can wear out over time.
plumbing-types-of-faucets
how-to-fix-a-leaky-faucet

Some jobs are better left to the pros

Consult a Pro. Get No-Commitment Estimates For Your Project.

What you’ll require

A number of the items you’ll require to stop a leaking faucet are currently in your tool kit. An Experienced Plumber encourages getting the following materials prior to beginning work:

 

  • Rags– for simple cleanup.
  • White vinegar– for cleaning along the way and losing grim accumulation in the spout.
  • A Philips and flat-head screwdriver– to take off the screw.
  • Replacement parts– to switch out the failed components.

 

You must likewise have an allen wrench or an adjustable wrench on hand to loosen nuts and valves. Slip-joint pliers can do the same job and supply a better grip on small faucet parts that require to be tightened during reassembly.

Repairing

Follow these steps to stop a leaking faucet, whether it’s a continuous leaky shower faucet or a leaking sink spout:

1. Turn off the water

Before doing any repair work, always switch off the water system. Look under the sink for the shutoff valves. Close them firmly by turning them clockwise.

Overtightening can trigger damage, so avoid using too much force. If the valves aren’t under the sink, you’ll require to close the main water valves.

These devices are generally found in the basement or near the washing unit, clothes dryer, or hot water heating system.

After you‘ve closed the valves, turn on the faucet to minimize the pressure and empty any remaining water in the pipes.

2. Close the drain

You’ll be working with tiny screws when you take off the faucet, and you do not want them to get lost down the drain pipes. Avoid a problem by covering up holes with coverings or plugs. A rag can likewise be placed down the pipe.

3. Take the system apart

Depending upon your sink, you may require to take off the faucet body to reach the issue, however preferably, you will just require to take off the handle.

For ceramic disc faucets, start by taking off the set screw and retaining nut prior to reinstalling the cylinder. The steps are comparable for a cartridge faucet, however you will require to take off the retaining clip or nut to replace the cartridge. As you take off the parts, keep the order and alignment in mind.

This attention to detail makes reassembly much easier. Set aside the pieces in the order you disassembled them to help you remember, or snap images as you work.

4. Inspect all the parts

When a faucet starts to leak, seals, rubber washers, and O-rings are typically to blame. Inspect them for noticeable indications of wear and tear, such as a flattened washer or grooves worn into the pieces.

If they appear used, replace them. Bring the old components with you to the shop to ensure you get the appropriate replacements.

Alternatively, replace the faucet with a washer-less one to help avoid the issue in the future.

5. Clean as you go

Use this time to clean up the pieces prior to reassembling them. Once the parts have actually been taken out, wash all seals and inside cylinders.

Inspect the valve seat for mineral deposits that might trigger the washer to become clogged and trigger leakages. Clean the surface areas with a small cloth and release the deposits by soaking them in white vinegar.

6. Reassemble the faucet

This is when the pictures you shot earlier come in useful. Reverse the disassembly process with your tools in hand to assemble the faucet. Never pressure parts to work or push down on the faucet.

7. Evaluate the water flow

After you‘ve completed the repair, you’ll require to turn the water back on. Expert advice: Ensure the faucet is turned on, and after that gradually turn the water back on.

If the faucet is shut off or too much pressure is applied prematurely, it may trigger more significant damage, such as cracking the ceramic disc. Enable the water to flow usually for a few minutes.

Think about replacing instead of fixing

If an old faucet is giving you issues, it’s normally a pretty good idea to replace it totally with a new cartridge model.

If you can’t identify what’s triggering the leak or if a quick remedy does not work, it’s better to hire a plumbing technician who has the abilities to efficiently identify and resolve the issue.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project

Proud to Install, Repair, and Service the Following Brands: